null

DENALI GEN II CANsmart & TriOptic LED D3 Bundle BMW R1250GSA

(No reviews yet) Write a Review

SKU:
DENALI-LKB-GSALC-D3-GSA
MPN:
DENALI-LKB-GSALC-D3-GSA
  • DENALI GEN II CANsmart & TriOptic LED D3 Bundle BMW R1250GSA (DENALI-LKB-GSALC-D3-GSA)
  • DENALI GEN II CANsmart & TriOptic LED D3 Bundle BMW  R1250GSA
  • DENALI GEN II CANsmart & TriOptic LED D3 Bundle BMW  R1250GSA
  • DENALI GEN II CANsmart & TriOptic LED D3 Bundle BMW  R1250GSA
  • DENALI GEN II CANsmart & TriOptic LED D3 Bundle BMW  R1250GSA
  • DENALI GEN II CANsmart & TriOptic LED D3 Bundle BMW  R1250GSA
£623.00
Frequently bought together:

Description

Simply select a pair of pods. We've pre-selected the correct CANsmart and light mount for your bike making even easier to get your plug 'n' play Denali system on your bike.

Whats in the bundle?

2 x TriOptic LED D3 PODS

2 x M8 Mounting Hardware Kit
2 x  Clear True-Hybrid Lens
2 x Wiring Pigtail


1 x CANsmart Controller

2 x 4ft light extension cables

1 x 5ft SoundBomb horn extension cable
1 x Brake light pigtail
1 x Adhesive hook-and-loop fastener
1 x Micro USB programming cable
Zip-ties

 

Can I fit this? (CANsmart Installation PDF Below)

It's relatively simple to fit a Denali bundle thanks to Denali's plug 'n' play Gen II CANsmart as I will briefly explain below. 

Connecting the CANsmart to the bike

First remove your rider & pillion seats, place the CANsmart in the pillion seat well & unplug the connector from the rear RCD. Plug the RDC connector into the male 4-pin connector on the CANsmart & plug the female 4-pin connector on the CANsmartTM Controller into the RDC unit.

Connecting to the battery

Remove the fuse from the fuse holder. Gain access to the vehicle’s battery and disconnect the negative (-) and positive (+) terminals.

Feed the CANsmart battery loom between the pillion & rider seat and down the right hand side of the bike to the battery. Be sure the orange wire lead with the fuse holder goes to the positive (+) terminal of the battery. Re-install the fuse into the fuse holder.

Connecting the Lights

Install the driving light mount under the beak of your GSA & loosely fit your pods. There is a couple of ways you can feed your light harness to the front of the bike. From the CANsmart feed the wires through from the pillion to the rider seat, you then you have a few of options, the easier two options are to feed the wires either side of the tank or remove the tank cover on your GSA and feed them up and over, alternatively you can lift the tank and feed the wires underneath, this method is considerably more work as you to strip most of the from top the bike. Once the wires have been fead through connect to the pods, switch the ignition on and you lights should come on, adjust the pods for height and tighten. You may have to configure your CANsmart first. p.s. always double check cable clearance especially around the forks & front spring.  

Connecting the Horn

Mount the horn using the bike specific mount in between the forks. Feed the horn wire in the same way as the lights and connect the two spades to the bottom of the horn. You will need to configure the horn channel using the hex software. p.s. this also fits the lowered frame GS.

DENALI 2.0 CANsmart Controller GEN II

Harness the flexibility and intelligence of your BMW motorcycle's CAN bus electrical system to make installation of accessories drastically easier with the new and improved DENALI CANsmart™ Controller GEN II.The DENALI CANsmart™ Controller provides plug-n-play installation and integrated control of up to four accessories to enable dozens of customizable settings that can be controlled right from the BMW "WonderWheel" or the CANsmart™ Accessory Manager Software. The CANsmart's four circuits are preprogrammed to connect and independently control two sets of DENALI lights, a SoundBomb horn, and our B6 auxiliary brake light.  

 

DENALI D3 2.0 TriOptic LED Light Pod (DENDNL.D3.050)

The new D3 LED lights are built upon a decade of DENALI innovation to deliver the highest performing 36-watt street-legal driving light to hit the market. Our D3 driving light features our signature TriOptic™ beam system that includes a spot and hybrid driving lens with each light pod. Unlike previous TriOptic™ lights, the D3 hybrid driving beam is ECE and SAE compliant to deliver an impressive street-legal high beam in North America and European Union countries. But what if you're not concerned with street-legal precision and just want off-road outrageous? We got you covered too! The D3 spot lens was engineered for maximum beam distance measuring over 1900 feet at 1 lux (per pair). No other 36-watt light even comes close. The spot beam is so impressive it actually outperforms top-tier competitor's lights that are twice it's size. 

View AllClose